I am lost on how to receive CAN message on STM32F4Discovery. I have it in Silent_Loopback mode, meaning all sent messages should arrive in CAN controller itself. I get Transmit_OK status when I send the message, however, nothing appears in the FIFO mailbox. I have skipped CAN filter configuration in order to receive all messages and not to filter any of them out. What am I doing wrong?
/* Includes */
#include "stm32f4xx.h"
#include "stm32f4_discovery.h"
void Delay(__IO uint32_t nCount) {
while(nCount--) {
}
}
void RCC_Configuration(void) {
/* ENABLE CLOCKS */
/* GPIOB clock enable */
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE);
/* USART3 clock enable */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE);
/* CAN1 clock enable */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_CAN1, ENABLE);
/* CAN2 clock enable */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_CAN2, ENABLE);
}
void GPIO_Configuration(void) {
GPIO_InitTypeDef GPIO_InitStructureUSART;
GPIO_InitTypeDef GPIO_InitStructureCAN_RX;
GPIO_InitTypeDef GPIO_InitStructureCAN_TX;
/* GPIO USART Configuration */
GPIO_InitStructureUSART.GPIO_Pin = GPIO_Pin_10 | GPIO_Pin_11;
GPIO_InitStructureUSART.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructureUSART.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructureUSART.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_InitStructureUSART.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOB, &GPIO_InitStructureUSART);
/* Connect USART to AF */
GPIO_PinAFConfig(GPIOB, GPIO_PinSource10, GPIO_AF_USART3); //USART_TX = PB10
GPIO_PinAFConfig(GPIOB, GPIO_PinSource11, GPIO_AF_USART3); //USART_RX = PB11
/* GPIO CAN_RX Configuration */
GPIO_InitStructureCAN_RX.GPIO_Pin = GPIO_Pin_12;
GPIO_InitStructureCAN_RX.GPIO_Mode = GPIO_Mode_AF;
//GPIO_InitStructureCAN_TX.GPIO_OType = GPIO_OType_PP;
//GPIO_InitStructureCAN_TX.GPIO_PuPd = GPIO_PuPd_NOPULL;
//GPIO_InitStructureCAN_TX.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOB, &GPIO_InitStructureCAN_RX);
/* GPIO CAN_TX Configuration */
GPIO_InitStructureCAN_TX.GPIO_Pin = GPIO_Pin_13;
GPIO_InitStructureCAN_TX.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructureCAN_TX.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructureCAN_TX.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_InitStructureCAN_TX.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOB, &GPIO_InitStructureCAN_TX);
/* Connect CAN_RX & CAN_TX to AF9 */
GPIO_PinAFConfig(GPIOB, GPIO_PinSource12, GPIO_AF_CAN2); //CAN_RX = PB12
GPIO_PinAFConfig(GPIOB, GPIO_PinSource13, GPIO_AF_CAN2); //CAN_TX = PB13
}
void USART_Configuration(void) {
USART_InitTypeDef USART_InitStructure;
/* USART3 configuration */
/* 256000 baud, window 8 data bits, one stop bit, no parity, no hardware flow control, rx/tx enabled */
USART_InitStructure.USART_BaudRate = 256000;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART3, &USART_InitStructure);
USART_Cmd(USART3, ENABLE);
}
void CAN_Configuration(void) {
CAN_InitTypeDef CAN_InitStructure;
/* CAN2 reset */
CAN_DeInit(CAN2);
/* CAN2 configuration */
CAN_InitStructure.CAN_TTCM = DISABLE; // Time-triggered communication mode = DISABLED
CAN_InitStructure.CAN_ABOM = DISABLE; // Automatic bus-off management mode = DISABLED
CAN_InitStructure.CAN_AWUM = DISABLE; // Automatic wake-up mode = DISABLED
CAN_InitStructure.CAN_NART = DISABLE; // Non-automatic retransmission mode = DISABLED
CAN_InitStructure.CAN_RFLM = DISABLE; // Receive FIFO locked mode = DISABLED
CAN_InitStructure.CAN_TXFP = DISABLE; // Transmit FIFO priority = DISABLED
CAN_InitStructure.CAN_Mode = CAN_Mode_Silent_LoopBack; // Normal CAN mode
CAN_InitStructure.CAN_SJW = CAN_SJW_1tq; // Synchronization jump width = 1
CAN_InitStructure.CAN_BS1 = CAN_BS1_14tq; //14
CAN_InitStructure.CAN_BS2 = CAN_BS2_6tq; //6
CAN_InitStructure.CAN_Prescaler = 4; // Baudrate 500 kbps
//CAN_InitStructure.CAN_Prescaler = 16; // Baudrate 125 kbps
if (CAN_Init(CAN2, &CAN_InitStructure)) { // Initialize CAN
STM_EVAL_LEDInit(LED6); // Initialize and
STM_EVAL_LEDOn(LED6); // Turn ON blue LED if CAN initialization is successful
}
}
void CAN_FilterConfiguration(void) {
CAN_FilterInitTypeDef CAN_FilterInitStructure;
/* CAN2 filter configuration */
CAN_FilterInitStructure.CAN_FilterNumber = 0; // Filter number = 0 (0<=x<=13)
CAN_FilterInitStructure.CAN_FilterMode = CAN_FilterMode_IdMask; // Filter mode = identifier mask based filtering
CAN_FilterInitStructure.CAN_FilterScale = CAN_FilterScale_16bit;
CAN_FilterInitStructure.CAN_FilterIdHigh = 0x0300 << 5; //0x0000;
CAN_FilterInitStructure.CAN_FilterIdLow = 0x0000;
CAN_FilterInitStructure.CAN_FilterMaskIdHigh = 0x03FF << 5;
CAN_FilterInitStructure.CAN_FilterMaskIdLow = 0x0000;
CAN_FilterInitStructure.CAN_FilterFIFOAssignment = CAN_FIFO0; // FIFO = 0
CAN_FilterInitStructure.CAN_FilterActivation = ENABLE;
CAN_FilterInit(&CAN_FilterInitStructure);
}
void CAN_TxMessage(void) {
CanTxMsg TxMessage;
/* CAN message to send */
TxMessage.StdId = 0x321;
TxMessage.ExtId = 0x01;
TxMessage.RTR = CAN_RTR_DATA;
TxMessage.IDE = CAN_ID_STD;
TxMessage.DLC = 8;
TxMessage.Data[0] = 0x04;
TxMessage.Data[1] = 0x01;
TxMessage.Data[2] = 0x00;
TxMessage.Data[3] = 0x00;
TxMessage.Data[4] = 0x00;
TxMessage.Data[5] = 0x00;
TxMessage.Data[6] = 0x00;
TxMessage.Data[7] = 0x00;
//while (1) {
CAN_TransmitStatus(CAN2, 0);
CAN_Transmit(CAN2, &TxMessage);
if(CAN_TransmitStatus(CAN2, 0)){
STM_EVAL_LEDInit(LED4); // Initialize and
STM_EVAL_LEDOn(LED4); // turn ON green LED if transmit was successful
}
//}
}
void CAN_OBDII_RequestCurrentData(int PIDNumber) {
CanTxMsg TxMessage;
TxMessage.StdId = 0x7DF; // PID request identifier
TxMessage.ExtId = 0x7DF;
TxMessage.RTR = CAN_RTR_DATA;
TxMessage.IDE = CAN_ID_STD;
TxMessage.DLC = 8;
TxMessage.Data[0] = 0x02; // Number of additional bytes = 2
TxMessage.Data[1] = 0x01; // Show current data = 1
TxMessage.Data[2] = PIDNumber; // PID code number
TxMessage.Data[3] = 0x00;
TxMessage.Data[4] = 0x00;
TxMessage.Data[5] = 0x00;
TxMessage.Data[6] = 0x00;
TxMessage.Data[7] = 0x00;
CAN_Transmit(CAN2, &TxMessage); // Transmit OBDII PID request via CAN2/mailbox0
}
void CAN_RxMessage(void) {
CanRxMsg RxMessage;
int d0=0;
while(1) {
CAN_Receive(CAN2,CAN_FIFO0,&RxMessage);
d0 = RxMessage.Data[0];
d0 = RxMessage.Data[1];
d0 = RxMessage.Data[2];
d0 = RxMessage.Data[3];
d0 = RxMessage.Data[4];
d0 = RxMessage.Data[5];
d0 = RxMessage.Data[6];
d0 = RxMessage.Data[7];
}
}
int main(void)
{
/* Initialize Clocks */
RCC_Configuration();
/* Initialize GPIO */
GPIO_Configuration();
/* Initialize USART */
USART_Configuration();
/* Initialize CAN */
CAN_Configuration();
/* Initialize CAN Reception Filter */
//CAN_FilterConfiguration();
/* Transfer CAN message */
CAN_TxMessage();
/* Receive CAN message */
CAN_RxMessage();
You have to configure filter to accept all messages (if you don’t have any filter, no message will be accepted). But in your example you use CAN2, so FilterNumber must be 14 or higher.